datasheet | october 2013 fiber optics | rev 2013.10 information contained herein is deemed reliable and accurate as of the issue date. emcore reserves the right to change the desi gn or specification at any time without notice. applications high-performance supertrunking links high-power distribution networks redundant ring architectures fttx networks rfog applications sat-if transport dwdm node splitting features single or dual optical outputs qam loading to 1003 mhz sat-if loading from 950 to 2800 mhz dual power supplies, redundant & hot swappable front panel rf test point vacuum fluorescent status display omi / rf gain adjustment agc select: cw, video, manual (no agc) industry leading field adjustable sbs suppression the j-type medallion 6000 series the j-type medallion 6000 series is a fami ly of state-of-the-ar t high-performance 1550 nm externally-modulated catv fiber optic transmitters optimized for varying network applications. packaged in a convenient 1 ru housing, this line of optical transmitters couples high optical output power, up to 10.0 db m, with low optical line width resulting in unmatched performance. the optical modulator, combined with proprietary pre-distortion circuitry, provides superior ctb and cso performance with sbs suppression levels of greater than 17 dbm for sat-if applications. the j-type transmitter?s exceptional performance is enabled by emcore?s proprietary high power, narrow line width cw (continuous wave) laser technology. when deployed with one or more emcore optical amplifie rs, transmissions of 150 km can be achieved. the feature-rich web gui and snmp interface bring a whole suite of advanced operator monitoring and configuration options to the platform, allowing for secure, simplified and future-ready functionality for the next generation of intelligent networks. advanced features such as built-in field adju stable sbs control allow these transmitters to be quickly optimized in the field for any link or application without the need to procure specifically tuned transmitters. the j-type series are designed as a high-performance solution for applications where the simultaneous, concurrent fiber optic tr ansport of catv and satellite-intermediate frequency signals (sat-if) is required. the sat-if signals can be applied anywhere in the 950 to 2800 mhz band. j-type transmitters are specially designed and optimized to support fiber optic links of up to 150 km for the japanese marketplace and ot her markets with similar requirements. monitoring and configuration is supported via a convenient front panel display, an rs-232 port, and an ethernet port with snmp, telnet, and web gui. the platform is mechanically designed for flexibility and space efficiency including universal rack-mount features, modular front panel design, and optional front and rear port placement. dual redundant field-replaceable fans and power supplies are standard. j-t y pe medallion 6000 1550 nm externally-modulated transmitter
datasheet | october 2013 fiber optics | rev 2013.10 information contained herein is deemed reliable and accurate as of the issue date. emcore reserves the right to change the desi gn or specification at any time without notice. optical characteristics property units 6000-0je1 comments performance (note 1-9) performance for channel plans with sat-if loading specified link length l (km) 25 25 25 channel plan ntsc 20+ 60-64 qam ntsc 80-ch pal 60-ch with 36 qpsk carriers from 950 to 2800 mhz optical output power po (dbm) 8.5/8.5 8.5/8.5 8.5/8.5 min. 10 dbm version avail. see chart noise bandwidth bw (mhz) 4 4 5 sbs suppression (dbm) 11 to 17 11 to 17 11 to 17 min. catv carrier to noise ratio cnr (db) 58.5 51.0 51.0 min. catv composite second order cso (dbc) -67 -65 -65 max. port 1 catv composite triple beat ctb (dbc) -67 -65 -65 max. @ +25 c catv composite triple beat ctb (dbc) -66 -64 -64 max. @ 0 o c to 50 o c sat-if carrier to noise ratio cnr (db) 27 27 27 min. sat-if intermodulation products (dbc) -35 -35 -35 max. port 1 sat-if spurious products (dbc) -38 -38 -38 max. property units 6000-0je1 comments performance (note 1-9) performance for channel plans without sat-if loading specified link length l (km) 25 25 25 channel plan ntsc 20+ 60-64 qam ntsc 80-ch pal 60-ch optical output power po (dbm) 8.5/8.5 8.5/8.5 8.5/8.5 min. 10 dbm version avail. see chart noise bandwidth bw (mhz) 4 4 5 sbs suppression (dbm) 11 to 17 11 to 17 11 to 17 min. catv carrier to noise ratio cnr (db) 58.5 53.0 53.0 min. catv composite second order cso (dbc) -67 -65 -65 max. port 1 catv composite triple beat ctb (dbc) -67 -65 -65 max. @ +25 c catv composite triple beat ctb (dbc) -66 -64 -64 max. @ 0 o c to 50 o c notes: 1. unless stated otherwise all spec ifications apply over full temper ature range with no digital loading. 2. unless stated otherwise specif ications apply for nominal rf input level as defined below, after a 30 minute stabilization p eriod. 3. specifications separated by a slash are port1 / port 2. 4. units are tested per the te st / link configuration table 5. noise figure for the edfa = 4.5 ~ 5.5 db 6. corning smf-28 single mode fiber 7. receiver responsivity is 0.95 ma/mw, equivalent noise current is 7 pa/(hz)1/2 8. with 36 qpsk modulated sat-if signals between 950 2800 mhz. 27 mhz if bandwidth 9. the lowest frequency of all channel plans shall be > 119.25 mh z. a 2 db penalty of cnr may occur for channels from 80 to 11 2.25 mhz test/link configuration property edfa link received power 2 j-type 14 dbm 25 km 0.0 dbm at the receiver j-t y pe medallion 6000 1550 nm externally-modulated transmitter
datasheet | october 2013 fiber optics | rev 2013.10 information contained herein is deemed reliable and accurate as of the issue date. emcore reserves the right to change the desi gn or specification at any time without notice. electrical specifications property requirement comments catv nominal input power 23 dbmv/ch (84 dbuv/ch) 18 dbmv/ch (78 dbuv/ch) 19 dbmv/ch (79 dbuv/ch) 20 ntsc channels + 60 qam at -10 db 80 ntsc channels 60 pal channels catv composite level -11.7 dbm 0 db on fp display (all channel plans) catv input range +2/-8 db from nominal input optimal performance at nominal input catv rf gain / omi adjustment range +2/-8 db from nominal setting catv performance may vary slightly over range catv frequency range 45 mhz ? 1003 mhz catv flatness +/- 0.50 db 45 mhz ? 550 mhz +/- 0.75 db 45 mhz ? 1003 mhz catv input impedance 75 catv input return loss 16 db min 45 mhz ? 1003 mhz catv front panel rf tap -20 +/- 1 db down from rf input catv front panel rf tap flatness +/- 1 db 45 mhz ? 1003 mhz sat nominal input power 27 dbmv/ch (87 dbuv/ch) 36 qpsk sat-if channels sat input range 22 ? 32 dbmv/ch (82 ? 92 dbuv/ch) optimum performance at nominal input sat composite level -6.2 dbm 0 db on fp display sat-if rf gain / omi adjustment range +5 / -5 db from nominal setting catv performance can vary slightly sat-if frequency range 950 mhz ? 2800 mhz sat-if flatness +/- 2 db sat-if input impedance 75 sat-if input return loss 10 db min 950 mhz ? 2800 mhz sat-if front panel rf tap 7 +/- 2.5 dbmv/ch at nominal omi/ch sat-if front panel rf tap flatness +/- 1 db 950 mhz ? 2800 mhz general and mechanical specifications property requirement comments wavelength 1555+/-5 nm various options + itu- grid available ? see model number information channel plan various ? see specification tables optical connector sc/apc other styles available monitoring interfaces 100 base-t ethernet (snmp) rear panel rs-232 interface vfd screen front panel controls vfd- (vacuum fluorescent display) operating temperature 0 c to 50 c storage temperature -20 c to 70 c power consumption 65 w max j-t y pe medallion 6000 1550 nm externally-modulated transmitter
datasheet | october 2013 fiber optics | rev 2013.10 information contained herein is deemed reliable and accurate as of the issue date. emcore reserves the right to change the desi gn or specification at any time without notice. general and mechanical specifications (continued) property requirement comments agency listings emi : en50083-2:2006 (us catv) en55022:2006 (us it) en61000-3-2 (harmonics) en61000-3-3 (flicker) fcc: part 15, subpart b, class ?a? unintentional radiators ices-003 (canada) an/nzs 3548, class a (australia) vcci, class a (japan) safety : fda/cdrh laser safety governed by code of federal regulations title 21, volume 8, part 1040 iec 60950-1 iec 60728-11 laser iec 60825-1 cb certification transportation vibration gr -2853-core in shipping package transportation shock gr-2853-core in shipping package operating humidity 20% to 85% non-condensing supply range (vac) (vdc) 90 to 265 vac, 50/60 hz +/- (36 ? 72) vdc dimensions 19.0? w x 15.0? d x 1.72? h (width includes 19? front panel ears, depth includes, connectors, fans & front panel) ? see drawing outline drawing j-t y pe medallion 6000 1550 nm externally-modulated transmitter
datasheet | october 2013 fiber optics | rev 2013.10 information contained herein is deemed reliable and accurate as of the issue date. emcore reserves the right to change the desi gn or specification at any time without notice. model number information note 3 6000 ? - logo & customer specific link type pout (dbm min) note 1 loading type optics rf wavelength (nm) power supply 0 ? emcore logo j ? 25 km d ? 10/10 note 4 1 ? all channel plans 1 ? sc/apc, rear 1 ? rf in rear, tp front 00 ?1555+/- 5.0 nm 1 ? ac primary, no secondary 1 ? no logo e ? 8.5/8.5 2 ? fc/apc, rear 2 ? rf in front, tp front 01 ? 1550+/- 5.0 nm 2 ? dc primary, no secondary 3 ? e2000/apc, rear 3 ? rf in front, tp rear xx ? itu channel +/- 0.1 nm note 2 3 ? ac primary, ac secondary 4 ? sc/apc, front 4 ? rf in rear, tp rear 4 ? ac primary, dc secondary 5 ? fc/apc, front 5 ? dc primary, dc secondary 6 ? e2000/apc, front note 1: options available for indicated types only note 2: itu grid wavelengths can be specified from channel 18 to 40 note 3: not all configurations are available, contact factory note 4: cso port 2 degraded by 1db note 5: contact factory for model type availability additional kits g3708-006-001 - replaceable ac power supply modules g3708-005-001 - replaceable dc power supply modules g7914-076-001 - replaceable blank power module plate g3906-008-001 - replaceable fans laser safety information this product meets the applicable requiremen ts of 21 cfr 1010 & 1040 and is classified as a class 1m laser product. during use as intended, the laser energy is fully contained within the fiber net work such that there is no accessible laser radiation. this p roduct has been issued accession number 0820466-001. j-t y pe medallion 6000 1550 nm externally-modulated transmitter
|
